릴레이로 전원 기기 전환하기
디지털 핀으로 램프나 팬을 켜고 끕니다.
릴레이로 전원 기기 전환하기은(는) CoddyKit의 무료 Arduino & IoT Academy 강의입니다. 이것은 4개 중 3번째 강의입니다. 아래에서 전체 강의를 무료로 읽을 수 있으며, 내장 코드 에디터와 24/7 AI 튜터와 함께 브라우저에서 직접 실습할 수 있습니다. 이 강의는 Arduino & IoT Academy 학습 경로의 일부이며, 진행 상황이 웹과 CoddyKit 앱에 동기화됩니다. Arduino & IoT Academy 강의에는 총 4개의 강의가 포함되어 있습니다.
이 강의의 일부는 아직 번역되지 않았으며 영어로 표시됩니다.
Controlling Big Things
Sometimes you want your Arduino to switch a lamp or a fan, not just an LED. For mains-powered gear you reach for a relay. 💡
A Relay Is a Switch
A relay is an electrically controlled switch. A small coil current pulls a metal contact closed, connecting a totally separate, much higher-power circuit.
Electrical Isolation
The coil and the contacts never touch electrically. This isolation is why a 5V Arduino can safely command a 220V device without sharing wires.
Use a Relay Module
Grab a ready-made relay module. It already has the driving transistor, a flyback diode, and screw terminals, so you just supply a control signal.
The Three Control Wires
A typical module has three pins: VCC, GND, and a signal input. Connect signal to any Arduino digital pin to control the relay.
Driving It in Code
Treat the relay like an LED. Set the pin HIGH or LOW to close or open the contact, depending on how your module is wired.
int relay = 7;
pinMode(relay, OUTPUT);
digitalWrite(relay, HIGH); // switch onActive-Low Surprise
Many modules are active-low: LOW turns the load on and HIGH turns it off. Test yours so the logic in your sketch matches reality.
NO and NC Terminals
The output side offers NO and NC contacts. Normally Open stays off until triggered; Normally Closed is on until the relay switches.
Wire the Load Through COM
Run one mains wire to the COM terminal and the other to NO. When the relay clicks, the circuit closes and your device powers up.
Respect Mains Safety
Mains voltage can kill. Never touch live terminals, keep the high-voltage side enclosed, and have an adult or pro check anything wired to the wall. ⚠️
Hear the Click
When the relay switches you hear a satisfying click as the coil snaps the contact. That sound confirms your code reached the real world.
Quick Check
What is the main reason a relay is used to switch mains-powered devices from an Arduino?
Recap
A relay is an isolated switch: a small signal closes contacts that power big loads. Use a module, mind active-low logic, and respect mains safety. 🚀
자주 묻는 질문
“릴레이로 전원 기기 전환하기” 강의는 무료인가요?
네 — “릴레이로 전원 기기 전환하기” 전체 내용을 이 웹사이트에서 무료로 읽을 수 있습니다. 인터랙티브하게 실습하려면(내장 코드 에디터와 24/7 AI 튜터), CoddyKit PRO로 업그레이드하면 Arduino & IoT Academy 강의 전체를 잠금 해제할 수 있습니다. Arduino & IoT Academy 강의에는 총 4개의 강의가 포함되어 있습니다.
“릴레이로 전원 기기 전환하기”에서 뭘 배우나요?
디지털 핀으로 램프나 팬을 켜고 끕니다. 브라우저에서 직접 실행하는 실습 코드로 Arduino & IoT Academy을(를) 배우며, 24/7 AI 튜터가 강의를 진행하면서 질문에 답변해줍니다.
Arduino & IoT Academy을(를) 시작하는 데 경험이 필요한가요?
사전 경험은 필요하지 않습니다. CoddyKit의 Arduino & IoT Academy은(는) 초급자부터 고급 학습자까지를 위해 구성되어 있으므로, 여기서 시작하거나 처음부터 시작할 수 있으며 자신의 속도대로 진행할 수 있습니다. 이것은 4개 중 3번째 강의입니다.
“릴레이로 전원 기기 전환하기” 강의는 얼마나 걸리나요?
대부분의 CoddyKit 강의는 약 5~10분이 소요됩니다. 각 강의는 간결하고 인터랙티브하여 꾸준한 진행이 가능하며, 웹과 앱에서 중단한 부분부터 바로 시작할 수 있습니다.
이 Arduino & IoT Academy 강의에서 코드를 작성하고 실행할 수 있나요?
네. 모든 Arduino & IoT Academy 강의에는 내장 코드 에디터가 포함되어 있으므로, 브라우저에서 바로 실제 코드를 작성하고 실행한 후 즉시 AI 피드백을 받을 수 있습니다 — 로컬 설정이 필요 없습니다.
이 강의의 모든 강의
- 드라이버가 필요한 이유
- H-브리지로 속도와 방향 제어하기
- 릴레이로 전원 기기 전환하기
- 역기전력으로 인한 급격한 전압 보호하기