가변 저항 손잡이 읽기
가변 저항을 연결하고 돌릴 때 값이 변하는 모습을 확인합니다
가변 저항 손잡이 읽기은(는) CoddyKit의 무료 Arduino & IoT Academy 강의입니다. 이것은 4개 중 3번째 강의입니다. 아래에서 전체 강의를 무료로 읽을 수 있으며, 내장 코드 에디터와 24/7 AI 튜터와 함께 브라우저에서 직접 실습할 수 있습니다. 이 강의는 Arduino & IoT Academy 학습 경로의 일부이며, 진행 상황이 웹과 CoddyKit 앱에 동기화됩니다. Arduino & IoT Academy 강의에는 총 4개의 강의가 포함되어 있습니다.
이 강의의 일부는 아직 번역되지 않았으며 영어로 표시됩니다.
Meet the Potentiometer
A potentiometer, or pot, is a knob you turn to change resistance. It is the easiest analog input to start experimenting with.
It Has Three Pins
A pot has three legs: two outer pins for power and ground, and a middle wiper pin that gives the changing voltage.
Wire the Outer Pins
Connect one outer pin to 5V and the other to GND. This sets up the full voltage range across the pot.
Wire the Wiper to A0
Run the middle wiper pin to an analog input like A0. As you turn the knob, the voltage on that pin moves.
It Is a Voltage Divider
Inside, the pot acts as a voltage divider. Turning the shaft moves a contact that splits 5V into the reading you sense.
Read the Knob in Code
Reading it is one line. Call analogRead(A0) and you get a value from 0 to 1023 that tracks the knob position.
int pot = analogRead(A0);Fully Left Reads 0
Turn the knob all the way toward the GND side and the reading drops to about 0. The wiper now sees zero volts.
Fully Right Reads 1023
Turn it fully toward the 5V side and the value climbs to about 1023. The wiper now sees the full supply voltage.
Print It to Watch
Send the value to the Serial Monitor so you can watch it change live. Use Serial.println inside your loop.
Serial.println(analogRead(A0));Add a Small Delay
A brief delay keeps the Serial Monitor readable instead of a blur. Ten milliseconds is plenty between samples.
delay(10);A Hands-On Analog Lab
The pot is your personal analog lab. Twisting it is the quickest way to feel how voltage becomes a number.
Quick Check
Which pot pin feeds the Arduino its reading?
Recap: Reading a Knob
You wired a potentiometer with outer pins on 5V and GND and the wiper on A0. Now analogRead tracks the knob from 0 to 1023.
자주 묻는 질문
“가변 저항 손잡이 읽기” 강의는 무료인가요?
네 — “가변 저항 손잡이 읽기” 전체 내용을 이 웹사이트에서 무료로 읽을 수 있습니다. 인터랙티브하게 실습하려면(내장 코드 에디터와 24/7 AI 튜터), CoddyKit PRO로 업그레이드하면 Arduino & IoT Academy 강의 전체를 잠금 해제할 수 있습니다. Arduino & IoT Academy 강의에는 총 4개의 강의가 포함되어 있습니다.
“가변 저항 손잡이 읽기”에서 뭘 배우나요?
가변 저항을 연결하고 돌릴 때 값이 변하는 모습을 확인합니다 브라우저에서 직접 실행하는 실습 코드로 Arduino & IoT Academy을(를) 배우며, 24/7 AI 튜터가 강의를 진행하면서 질문에 답변해줍니다.
Arduino & IoT Academy을(를) 시작하는 데 경험이 필요한가요?
사전 경험은 필요하지 않습니다. CoddyKit의 Arduino & IoT Academy은(는) 초급자부터 고급 학습자까지를 위해 구성되어 있으므로, 여기서 시작하거나 처음부터 시작할 수 있으며 자신의 속도대로 진행할 수 있습니다. 이것은 4개 중 3번째 강의입니다.
“가변 저항 손잡이 읽기” 강의는 얼마나 걸리나요?
대부분의 CoddyKit 강의는 약 5~10분이 소요됩니다. 각 강의는 간결하고 인터랙티브하여 꾸준한 진행이 가능하며, 웹과 앱에서 중단한 부분부터 바로 시작할 수 있습니다.
이 Arduino & IoT Academy 강의에서 코드를 작성하고 실행할 수 있나요?
네. 모든 Arduino & IoT Academy 강의에는 내장 코드 에디터가 포함되어 있으므로, 브라우저에서 바로 실제 코드를 작성하고 실행한 후 즉시 AI 피드백을 받을 수 있습니다 — 로컬 설정이 필요 없습니다.