브로커에 연결하기
PubSubClient를 사용해 MQTT 서버에 연결합니다.
브로커에 연결하기은(는) CoddyKit의 무료 Arduino & IoT Academy 강의입니다. 이것은 4개 중 2번째 강의입니다. 아래에서 전체 강의를 무료로 읽을 수 있으며, 내장 코드 에디터와 24/7 AI 튜터와 함께 브라우저에서 직접 실습할 수 있습니다. 이 강의는 Arduino & IoT Academy 학습 경로의 일부이며, 진행 상황이 웹과 CoddyKit 앱에 동기화됩니다. Arduino & IoT Academy 강의에는 총 4개의 강의가 포함되어 있습니다.
이 강의의 일부는 아직 번역되지 않았으며 영어로 표시됩니다.
You Need a Broker First
Before any messages flow, your device must reach a broker. It is the server that accepts connections and routes every message.
Public or Private Brokers
You can use a free public broker like test.mosquitto.org for learning, or run your own private one for real projects.
The PubSubClient Library
On ESP boards the popular choice is the PubSubClient library. Install it once, then include it at the top of your sketch.
#include <PubSubClient.h>It Rides on a WiFi Client
PubSubClient needs a network client to ride on. You hand it a WiFiClient that has already joined your network.
WiFiClient espClient;
PubSubClient client(espClient);Point It at the Broker
Tell the client where the broker lives with its address and port. Plain MQTT uses port 1883 by default.
client.setServer("test.mosquitto.org", 1883);Give Each Device a Client ID
Every connection needs a unique client ID. If two devices share one, the broker kicks the older connection off.
Make the Connection
Call connect with your client ID to log in. It returns true when the broker accepts you and false if something is wrong.
client.connect("esp32-sensor-01");Reconnect When It Drops
Connections die on real networks. Wrap your connect in a loop so the device keeps retrying until it is back online.
Keep the Link Alive
You must call client.loop() often inside loop(). It handles keepalive pings and incoming messages behind the scenes.
void loop() {
client.loop();
}Authenticate When Needed
Private brokers usually want a username and password. Pass them to connect so only trusted devices get in.
client.connect("id", "user", "pass");Watch the Connection State
Print the result of connect or check client.state() to debug. Clear logs save you from guessing why nothing arrives.
Quick Check
Your ESP32 sketch compiles but never receives messages, even though it connected once. What is the likely cause?
Recap
You connected to a broker with PubSubClient: set the server and port, used a unique client ID, and kept the link alive. 🎉
자주 묻는 질문
“브로커에 연결하기” 강의는 무료인가요?
네 — “브로커에 연결하기” 전체 내용을 이 웹사이트에서 무료로 읽을 수 있습니다. 인터랙티브하게 실습하려면(내장 코드 에디터와 24/7 AI 튜터), CoddyKit PRO로 업그레이드하면 Arduino & IoT Academy 강의 전체를 잠금 해제할 수 있습니다. Arduino & IoT Academy 강의에는 총 4개의 강의가 포함되어 있습니다.
“브로커에 연결하기”에서 뭘 배우나요?
PubSubClient를 사용해 MQTT 서버에 연결합니다. 브라우저에서 직접 실행하는 실습 코드로 Arduino & IoT Academy을(를) 배우며, 24/7 AI 튜터가 강의를 진행하면서 질문에 답변해줍니다.
Arduino & IoT Academy을(를) 시작하는 데 경험이 필요한가요?
사전 경험은 필요하지 않습니다. CoddyKit의 Arduino & IoT Academy은(는) 초급자부터 고급 학습자까지를 위해 구성되어 있으므로, 여기서 시작하거나 처음부터 시작할 수 있으며 자신의 속도대로 진행할 수 있습니다. 이것은 4개 중 2번째 강의입니다.
“브로커에 연결하기” 강의는 얼마나 걸리나요?
대부분의 CoddyKit 강의는 약 5~10분이 소요됩니다. 각 강의는 간결하고 인터랙티브하여 꾸준한 진행이 가능하며, 웹과 앱에서 중단한 부분부터 바로 시작할 수 있습니다.
이 Arduino & IoT Academy 강의에서 코드를 작성하고 실행할 수 있나요?
네. 모든 Arduino & IoT Academy 강의에는 내장 코드 에디터가 포함되어 있으므로, 브라우저에서 바로 실제 코드를 작성하고 실행한 후 즉시 AI 피드백을 받을 수 있습니다 — 로컬 설정이 필요 없습니다.