Misurazione del gas
Strumenti di profiling
Misurazione del gas è una lezione Web3 & DApp Development Fundamentals gratuita su CoddyKit. Questa è la lezione 4 di 4. Puoi leggere la lezione completa qui gratuitamente — poi esercitati direttamente nel browser con un editor di codice integrato e un tutor IA disponibile 24/7. Fa parte del percorso di apprendimento Web3 & DApp Development Fundamentals, e i tuoi progressi si sincronizzano tra il web e l'app CoddyKit. Il corso Web3 & DApp Development Fundamentals include 4 lezioni in totale.
Parti di questa lezione non sono ancora state tradotte e vengono mostrate in inglese.
Measure, Don't Guess
Gas optimization without measurement is guesswork. The compiler, opcode costs, and access patterns interact in non-obvious ways, so an intuitive change can sometimes make things worse.
Always profile before and after. A change that does not reduce measured gas is not an optimization, no matter how clever it looks.
Forge Gas Reports
Foundry's forge test --gas-report prints a per-function table of min, average, median, and max gas usage across all your tests. It is the fastest way to spot expensive functions.
$ forge test --gas-report
| Function | min | avg | median | max | # calls |
| transfer | 28012 | 34521 | 34521 | 51012 | 12 |
| approve | 24300 | 24300 | 24300 | 24300 | 5 |Gas Snapshots
forge snapshot writes the gas cost of every test to a .gas-snapshot file. Commit it to version control, then run forge snapshot --diff to see exactly how a change affected gas.
This turns gas regressions into reviewable diffs in pull requests.
$ forge snapshot
$ forge snapshot --diff
testTransfer() (gas: -1240 (-3.6%))
testMint() (gas: +85 (+0.2%))Measuring in Tests
For fine-grained measurement, read gasleft() before and after a call inside a test. The difference is the gas consumed by that block of code.
uint256 before = gasleft();
target.doWork();
uint256 used = before - gasleft();
emit log_named_uint("gas used", used);Verbose Traces
Running tests with -vvvv shows a full execution trace including the gas cost of each external call and opcode group. This reveals where gas is spent, not just the total.
$ forge test --match-test testTransfer -vvvv
[34521] Token::transfer(bob, 100)
emit Transfer(from: alice, to: bob, value: 100)
return: trueThe Optimizer Setting
The Solidity optimizer changes runtime and deployment gas. The runs parameter is a hint about how often functions are called.
- Low
runs(e.g. 1) optimizes for cheap deployment - High
runs(e.g. 10000) optimizes for cheap repeated calls
Set it in foundry.toml and always measure with the optimizer enabled, since it reflects production behavior.
# foundry.toml
[profile.default]
optimizer = true
optimizer_runs = 10000Comparing Implementations
To compare two approaches, write a test that exercises each under identical conditions and inspect the gas report side by side.
Keep inputs the same and isolate the change to one variable, otherwise you cannot attribute the gas difference to the optimization you made.
function testNaive() public { c.sumNaive(data); }
function testOptimized() public { c.sumOptimized(data); }
// compare both rows in --gas-reportBeware Warm vs Cold Skew
Gas reports can mislead because the first access in a test is cold and later ones are warm. A function called once in setup may show a higher cold cost than the same function later.
Look at min, median, and max columns together rather than a single average, and design tests that reflect real-world access patterns.
Etherscan and Real Receipts
On-chain transaction receipts report the actual gasUsed. Etherscan and block explorers display this for every transaction, letting you validate your local measurements against mainnet reality.
The eth_estimateGas RPC method gives a pre-flight estimate, though it adds a safety margin and may differ from the real execution cost.
CI Gas Regression Gates
Wire forge snapshot --check into continuous integration. It fails the build if any test's gas exceeds the committed snapshot beyond a tolerance.
This prevents accidental gas regressions from slipping into production and makes gas a first-class quality metric.
$ forge snapshot --check
# exits non-zero if gas increased vs committed snapshotA Measurement Workflow
A solid gas workflow:
- Write tests covering the hot paths
- Record a baseline with
forge snapshot - Make one optimization at a time
- Run
forge snapshot --diffto confirm the gain - Gate regressions in CI with
--check
Discipline beats cleverness.
Quick Check
Which Foundry command produces a per-function table of min, average, and max gas usage?
Recap
You learned to measure gas:
forge test --gas-reportfor per-function tablesforge snapshot --diffto track changesgasleft()for fine-grained measurement- Verbose traces reveal where gas goes
- Gate regressions in CI with
--check
This completes the Gas Optimization course. Next: the Foundry toolkit in depth.
Domande Frequenti
La lezione «Misurazione del gas» è gratuita?
Sì — il testo completo di «Misurazione del gas» è gratuito qui sul web. Per esercitarvi in modo interattivo (un editor di codice integrato e un tutor IA 24/7) e sbloccare il resto del corso Web3 & DApp Development Fundamentals, passa a CoddyKit PRO. Il corso Web3 & DApp Development Fundamentals include 4 lezioni in totale.
Cosa imparerò in «Misurazione del gas»?
Strumenti di profiling Eserciti Web3 & DApp Development Fundamentals con codice pratico che esegui direttamente nel browser, e un tutor IA 24/7 risponde alle tue domande mentre lavori sulla lezione.
Ho bisogno di esperienza per iniziare Web3 & DApp Development Fundamentals?
Non è richiesta alcuna esperienza precedente. Web3 & DApp Development Fundamentals su CoddyKit è strutturato per principianti e studenti avanzati, quindi puoi iniziare da qui o dall'inizio e procedere al tuo ritmo. Questa è la lezione 4 di 4.
Quanto tempo richiede la lezione «Misurazione del gas»?
La maggior parte delle lezioni CoddyKit richiede circa 5–10 minuti. Ogni lezione è breve e interattiva, quindi fai progressi costanti e riprendi esattamente da dove hai lasciato su web e app.
Posso scrivere ed eseguire codice in questa lezione Web3 & DApp Development Fundamentals?
Sì. Ogni lezione Web3 & DApp Development Fundamentals include un editor di codice integrato, quindi scrivi ed esegui codice reale direttamente nel tuo browser e ricevi feedback istantaneo dall'IA — nessuna configurazione locale necessaria.