Medición del gas
Herramientas de profiling
Medición del gas es una lección gratuita de Web3 & DApp Development Fundamentals en CoddyKit. Esta es la lección 4 de 4. Puedes leer la lección completa abajo gratuitamente — luego la practicas en el navegador con un editor de código integrado y un tutor de IA 24/7. Forma parte de la ruta de aprendizaje de Web3 & DApp Development Fundamentals, y tu progreso se sincroniza en la web y la app de CoddyKit. El curso de Web3 & DApp Development Fundamentals incluye 4 lecciones en total.
Partes de esta lección aún no han sido traducidas y se muestran en inglés.
Measure, Don't Guess
Gas optimization without measurement is guesswork. The compiler, opcode costs, and access patterns interact in non-obvious ways, so an intuitive change can sometimes make things worse.
Always profile before and after. A change that does not reduce measured gas is not an optimization, no matter how clever it looks.
Forge Gas Reports
Foundry's forge test --gas-report prints a per-function table of min, average, median, and max gas usage across all your tests. It is the fastest way to spot expensive functions.
$ forge test --gas-report
| Function | min | avg | median | max | # calls |
| transfer | 28012 | 34521 | 34521 | 51012 | 12 |
| approve | 24300 | 24300 | 24300 | 24300 | 5 |Gas Snapshots
forge snapshot writes the gas cost of every test to a .gas-snapshot file. Commit it to version control, then run forge snapshot --diff to see exactly how a change affected gas.
This turns gas regressions into reviewable diffs in pull requests.
$ forge snapshot
$ forge snapshot --diff
testTransfer() (gas: -1240 (-3.6%))
testMint() (gas: +85 (+0.2%))Measuring in Tests
For fine-grained measurement, read gasleft() before and after a call inside a test. The difference is the gas consumed by that block of code.
uint256 before = gasleft();
target.doWork();
uint256 used = before - gasleft();
emit log_named_uint("gas used", used);Verbose Traces
Running tests with -vvvv shows a full execution trace including the gas cost of each external call and opcode group. This reveals where gas is spent, not just the total.
$ forge test --match-test testTransfer -vvvv
[34521] Token::transfer(bob, 100)
emit Transfer(from: alice, to: bob, value: 100)
return: trueThe Optimizer Setting
The Solidity optimizer changes runtime and deployment gas. The runs parameter is a hint about how often functions are called.
- Low
runs(e.g. 1) optimizes for cheap deployment - High
runs(e.g. 10000) optimizes for cheap repeated calls
Set it in foundry.toml and always measure with the optimizer enabled, since it reflects production behavior.
# foundry.toml
[profile.default]
optimizer = true
optimizer_runs = 10000Comparing Implementations
To compare two approaches, write a test that exercises each under identical conditions and inspect the gas report side by side.
Keep inputs the same and isolate the change to one variable, otherwise you cannot attribute the gas difference to the optimization you made.
function testNaive() public { c.sumNaive(data); }
function testOptimized() public { c.sumOptimized(data); }
// compare both rows in --gas-reportBeware Warm vs Cold Skew
Gas reports can mislead because the first access in a test is cold and later ones are warm. A function called once in setup may show a higher cold cost than the same function later.
Look at min, median, and max columns together rather than a single average, and design tests that reflect real-world access patterns.
Etherscan and Real Receipts
On-chain transaction receipts report the actual gasUsed. Etherscan and block explorers display this for every transaction, letting you validate your local measurements against mainnet reality.
The eth_estimateGas RPC method gives a pre-flight estimate, though it adds a safety margin and may differ from the real execution cost.
CI Gas Regression Gates
Wire forge snapshot --check into continuous integration. It fails the build if any test's gas exceeds the committed snapshot beyond a tolerance.
This prevents accidental gas regressions from slipping into production and makes gas a first-class quality metric.
$ forge snapshot --check
# exits non-zero if gas increased vs committed snapshotA Measurement Workflow
A solid gas workflow:
- Write tests covering the hot paths
- Record a baseline with
forge snapshot - Make one optimization at a time
- Run
forge snapshot --diffto confirm the gain - Gate regressions in CI with
--check
Discipline beats cleverness.
Quick Check
Which Foundry command produces a per-function table of min, average, and max gas usage?
Recap
You learned to measure gas:
forge test --gas-reportfor per-function tablesforge snapshot --diffto track changesgasleft()for fine-grained measurement- Verbose traces reveal where gas goes
- Gate regressions in CI with
--check
This completes the Gas Optimization course. Next: the Foundry toolkit in depth.
Preguntas frecuentes
¿La lección «Medición del gas» es gratis?
Sí — el texto completo de «Medición del gas» es gratis para leer aquí en la web. Para practicarla de forma interactiva (editor de código integrado y tutor de IA 24/7) y desbloquear el resto del curso de Web3 & DApp Development Fundamentals, actualiza a CoddyKit PRO. El curso de Web3 & DApp Development Fundamentals incluye 4 lecciones en total.
¿Qué aprenderé en «Medición del gas»?
Herramientas de profiling Practicas Web3 & DApp Development Fundamentals con código real que ejecutas directamente en el navegador, y un tutor de IA 24/7 responde tus preguntas mientras trabajas en la lección.
¿Necesito experiencia previa para empezar Web3 & DApp Development Fundamentals?
No se requiere experiencia previa. Web3 & DApp Development Fundamentals en CoddyKit está estructurado para principiantes hasta estudiantes avanzados, así que puedes empezar aquí o desde el inicio y avanzar a tu ritmo. Esta es la lección 4 de 4.
¿Cuánto tiempo toma la lección «Medición del gas»?
La mayoría de las lecciones de CoddyKit toman alrededor de 5–10 minutos. Cada una es compacta e interactiva, así que avanzas constantemente y retomas exactamente por donde dejaste en la web y la app.
¿Puedo escribir y ejecutar código en esta lección de Web3 & DApp Development Fundamentals?
Sí. Cada lección de Web3 & DApp Development Fundamentals incluye un editor de código integrado, así que escribes y ejecutas código real directamente en tu navegador y obtienes retroalimentación instantánea de IA — sin configuración local necesaria.